Google Pixel 9 Pro Rear Cameras Replacement

Werkzeuge

• 3IP Torx Plus Bit Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Angled Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• ESD Safe Blunt Nose Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• iFixit Opening Picks (Set of 6) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• iFixit Precision Bit Driver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Isopropyl Alcohol Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Microfiber Cleaning Cloths Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
• Suction Handle Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• T3 Torx Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Ersatzteile

• Google Pixel 9 Pro Rear Camera - Genuine Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

1. Safety precautions

   • 
   • 

   Unplug all cables and completely power down your phone.

2. Adhesive information

   • 
   • 
   • 

   Adhesive secures the perimeter of the rear cover to the frame.

3. Apply a suction handle

   • 
   • 

   Attach a suction handle to the bottom edge of the rear cover, as close to the edge as possible.

4. Insert an opening pick

   • 
   • 
   • 

   Pull up on the suction handle with strong, steady force to create a small gap under the rear cover.

   Insert the tip of an opening pick in the gap.

5. Separate the rear cover adhesive

   • 
   • 
   • 

   Slide your opening pick along the bottom edge to separate the adhesive securing it.

6. Step 6

   • 
   • 
   • 

   Slide your opening pick up the left edge and along the top edge to separate the adhesive.

7. Step 7

   • 
   • 
   • 

   Slide your pick down the right edge to separate the remaining adhesive.

8. Prop up the rear cover

   • 
   • 
   • 

   Use the suction handle to lift the left edge of the rear cover and swing it over the right edge, like opening the cover of a book.

   Prop up the rear cover with the suction handle so you can access the ribbon cable near the top right corner.

9. Remove the wireless charging assembly

   • 
   • 

   Use a Torx Plus 3IP screwdriver to remove the five screws securing the wireless charging assembly:

   Four 5.4 mm‑long screws

   One 1.5 mm‑long screw

10. Step 10

    • 
    • 
    • 

    Use tweezers or your fingers to remove the wireless charging assembly.

11. Disconnect the rear cover

    • 
    • 
    • 

    Insert the tip of an opening pick under the left edge of the rear cover press connector and pry straight up to disconnect it.

12. Remove the rear cover

    • 

    Remove the rear cover.

13. Remove the cable cover

    • 
    • 

    Use a Torx Plus 3IP screwdriver to remove the two screws securing the cable cover:

    One 2.3 mm‑long screw

    One 5.4 mm‑long screw

14. Step 14

    • 
    • 

    Use tweezers or your fingers to remove the cable cover.

15. Disconnect the battery

    • 
    • 
    • 

    Insert the point of a spudger under the right edge of the battery press connector and pry straight up to disconnect it.

16. Remove the 5G mmWave cover screw

    • 
    • 

    Use a Torx Plus 3IP screwdriver to remove the 5.4 mm‑long screw securing the mmWave antenna cover.

17. Unclip the 5G mmWave cover

    • 
    • 
    • 

    Insert the point of a spudger under the clip near the bottom left corner of the mmWave antenna cover and pry up to unclip it.

18. Remove the 5G mmWave cover

    • 
    • 

    Gently pull the right edge of the cover towards the bottom of the phone and remove the cover.

19. Disconnect the 5G mmWave antenna

    • 
    • 

    Use the point of a spudger to pry up and disconnect the mmWave antenna press connector from the top right corner of the logic board.

20. Disconnect the front facing camera

    • 
    • 

    Use the point of a spudger to pry up and disconnect the front facing camera press connector.

21. Remove the 5G mmWave antenna screw

    • 
    • 
    • 

    Carefully hold the front facing camera cable out of the way so you can access the mmWave antenna screw.

    Use a Torx Plus 3IP screwdriver to remove the 4.3 mm‑long screw securing the mmWave antenna.

22. Remove the 5G mmWave antenna

    • 
    • 

    Use tweezers or your fingers to remove the mmWave antenna.

23. Disconnect the interconnect cables

    • 
    • 
    • 

    Use the flat end of a spudger to pry up and disconnect the press connector near the bottom left corner of the logic board.

    Use the point of a spudger to disconnect the press connector just to the right of the previous one.

24. Step 24

    • 
    • 

    Insert the tip of an opening pick under the top edge of the press connector near the bottom right corner of the logic board.

    Use the pick to pry up and disconnect the press connector.

25. Remove the antenna board cover

    • 
    • 

    Use a Torx Plus 3IP screwdriver to remove the 5.4 mm‑long screw securing the antenna cover in the top left corner.

26. Step 26

    • 
    • 

    Use tweezers or your fingers to remove the cover.

27. Disconnect the antenna board

    • 
    • 
    • 

    Use the point of a spudger to pry up and disconnect the autofocus sensor press connector from the top left corner.

    Carefully move the cable out of the way so you can access the metal antenna connector underneath.

28. Step 28

    • 
    • 

    Slide one arm of your angled tweezers under the metal neck of the antenna connector and lift straight up to disconnect it.

29. Remove the logic board

    • 
    • 
    • 

    Use a spudger to pry up the top edge of the logic board until you can grip it with your fingers.

    Grip the right side of the logic board and carefully remove it, being careful that no cables get snagged (one front facing camera cable and four cables along the bottom edge).

30. Reassembly information

    • 
    • 
    • 

    Check the condition of the logic board thermal pad—it will either be on the bottom of the logic board or on the frame.

    If the pad is undamaged, skip the rest of this step.

    If the pad is damaged, use the flat end of a spudger to scrape it up and remove it.

    Use isopropyl alcohol (greater than 90%) and a microfiber cloth to remove all thermal pad residue from the frame and bottom of the logic board.

    Apply a new thermal pad to its spot on the frame.

31. Disconnect the rear cameras

    • 
    • 
    • 

    Hold the logic board above your work surface while disconnecting the rear cameras—don't press the board against your work surface, or you may damage fragile components.

    Use the point of a spudger to pry up and disconnect the autofocus sensor press connector on the top of the logic board, near the left edge.

32. Step 32

    • 
    • 
    • 

    Carefully flip the logic board over so the bottom is facing up.

    Use the point of a spudger to pry up and disconnect the three camera press connectors.

33. Remove the rear cameras

    • 
    • 
    • 

    Hold the logic board in one hand, and use your free hand to gently remove the rear cameras.

34. Remove the autofocus sensor

    • 
    • 

    Apply a heated iOpener to the top of the rear cameras to heat the adhesive securing the autofocus sensor.

35. Step 35

    • 
    • 
    • 

    Gently slide the flat end of a spudger under the bottom right corner of the autofocus sensor (near the cable) to begin separating the adhesive.

    Continue sliding the spudger under the perimeter of the sensor to separate the remaining adhesive.

36. Step 36

    • 
    • 
    • 

    Use your fingers to remove the autofocus sensor.

    Remove any adhesive on the underside of the sensor with a pair of tweezers.

37. Apply new autofocus sensor adhesive

    • 
    • 
    • 

    Remove the larger, clear plastic liner from your replacement autofocus sensor adhesive.

    Carefully apply the adhesive to the bottom of the sensor and press down firmly with a spudger to secure it.

    Peel up the remaining blue liner.

38. Step 38

    • 
    • 
    • 

    If your replacement rear cameras have protective caps or liners, remove them.

    Before applying the autofocus sensor to your replacement rear cameras, hold the sensor over your replacement cameras and find its proper orientation.

    Carefully lay the sensor over the rear camera and use your fingers to press it into place, securing it with the adhesive.

Abschluss

To reassemble your device, follow these instructions in reverse order starting with this step.

To run a diagnostics test with the built-in Pixel Diagnostic tool, click here.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.