iPhone 15 Pro Max Earpiece Speaker Replacement

Gerät: iPhone 15 Pro Max
Schwierigkeit: Mittel
Geschätzte Dauer: ⏱ 1 h

Use this guide to replace the earpiece speaker in your iPhone 15 Pro Max.

If the sound coming through your iPhone, especially during phone calls, sounds like static or crackling, your earpiece speaker may need to be replaced.

You'll need replacement screen adhesive to complete this repair.

Reparatur anfragen →

Lieber von uns ausführen lassen? Angebot innerhalb eines Werktages.

Werkzeuge

Hair Dryer Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Heat Gun Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
iFixit Opening Picks (Set of 6) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Isopropyl Alcohol Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Microfiber Cleaning Cloths Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
P2 Pentalobe Screwdriver iPhone Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Phillips #000 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
Suction Handle Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Tri-point Y000 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Ersatzteile

iPhone 15 Pro Max Earpiece Speaker Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

Prepare your phone for disassembly
Vorsicht: Caution Allow your phone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard.

Unplug any cables from your phone.

Hold the power and either volume buttons and slide to power off your phone.
Tape over any cracks
If your screen or back glass is badly cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.

Hinweis: Note Make sure there's a smooth area near the bottom edge that's big enough for a suction cup to stick to.
Mark your opening picks
Hinweis: Note If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.

Measure 3 mm from the tip and mark the opening pick with a permanent marker.

Hinweis: Note You can also mark the other corners of the pick with different measurements.

Hinweis: Note Alternatively, <a href="https://guide-images.cdn.ifixit.com/igi/pQGATIGUbViSB4gB.full" target="_blank">tape a coin to a pick</a> 3 mm from the tip.
Remove the pentalobe screws
Use a P2 pentalobe driver to remove the two 7.2 mm-long screws on either side of the charging port.
Heat the bottom edge
Use a hair dryer or heat gun to heat the bottom edge of the screen until it's hot to the touch.

Vorsicht: Caution Be careful not to heat the phone hotter than this—the battery is susceptible to heat damage.
Insert an opening pick
Apply a suction handle to the bottom edge of the screen.

Pull up on the handle with a strong, steady force to create a gap between the screen and the frame.

Insert the tip of an opening pick into the gap.
Screen information
Vorsicht: Caution As you slice the adhesive securing the screen in the next steps, be careful of the following areas:

There are two delicate cables connecting the screen to the phone: one just above the action button, and the other near the middle of the left edge.

There are multiple spring contacts around the perimeter of the phone. Be extra careful not to insert your pick deeper than suggested in these locations to avoid bending the contacts.
Separate the bottom edge adhesive
Vorsicht: Caution Don't insert your opening pick deeper than 3 mm along the bottom edge.

Slide your pick back and forth along the bottom edge to separate the adhesive.

Leave your pick inserted in the bottom right corner to prevent the adhesive from re-sealing.
Heat the right edge
Heat the right edge of the screen until it's hot to the touch.
Position the opening pick
Vorsicht: Caution Don't insert your pick deeper than 5 mm along the right edge.

Slide your pick around the bottom right corner of the screen and toward the power button until you feel a hard stop at a clip securing the screen.

Rotate your pick so the flat edge is under the screen.
Release the right clip
Twist the pick to increase the gap between the screen and the frame until the right clip releases.

Insert a second opening pick to the right of the first pick.
Separate the right edge adhesive
Slide the first pick back to the bottom right corner of the screen.

Slide the second pick to the top right corner of the screen to separate the adhesive.

Leave these picks inserted to prevent the adhesive from resealing.
Heat the top edge
Heat the top edge of the screen until it's hot to the touch.
Separate the top edge adhesive
Vorsicht: Caution Don't insert your pick deeper than 3 mm along the top edge.

Slide your pick around the top right corner and along the top edge to release the two clips and adhesive securing it.
Heat the left edge
Heat the left edge of the screen until it's hot to the touch.
Separate the left edge adhesive
Vorsicht: Caution Don't insert your pick deeper than 2 mm along the left edge to avoid the <a href="https://guide-images.cdn.ifixit.com/igi/QXhBuOBJJOa41ccu.huge" target="_blank">two cables connecting the screen to the phone</a>.

Rotate your pick around the top left corner of the screen.

Slide your pick to the bottom left corner of the screen to separate the adhesive.
Swing open the screen
Gently swing open the screen to the left of the phone.

Hinweis: Note If the screen feels stuck, go back around the perimeter to check for missed sections of adhesive or stuck clips.

Rest the screen against a box or similar object so it doesn't strain the cables.
Unfasten the logic board cover
Hinweis: Note Throughout this repair, <a href="https://www.ifixit.com/en-eu/products/fixmat" target="_blank" class="product-link">keep track of each screw</a> and make sure it goes back exactly where it came from.

Use a tri-point Y000 driver to remove the six screws securing the logic board cover:

One 2.1 mm‑long screw

Five 1.5 mm‑long screws
Remove the logic board cover
Use tweezers or your fingers to grab and slide the logic board cover toward the bottom of the phone to clear the sensor cable.

Remove the cover.
Disconnect the battery
Use the tip of an opening pick to pry up and disconnect the battery press connector.

Hinweis: Note To reconnect a <a href="https://www.ifixit.com/Guide/Recognizing+&+Disconnecting+Cable+Connectors/25629#s70308" target="_blank">press connector</a>, align it over its socket and gently press down on one side until it clicks into place, then press down on the other side. Make sure it sits flat, as the insulating rubber around the sockets might prevent it from connecting fully.
Disconnect the ambient light sensor
Use the point of a spudger to pry up and disconnect the ambient light sensor press connector from the top left of the logic board.
Disconnect the screen
Disconnect the screen press connector.
Remove the screen
Remove the screen.

Erinnerung: Reminder During reassembly, stop here and <a href="https://www.ifixit.com/Guide/iPhone+Display+Adhesive+Replacement/93983" target="_blank">use this guide</a> to install new screen adhesive.

Vorsicht: Caution Be careful not to damage any of the <a href="https://guide-images.cdn.ifixit.com/igi/RHTxaTCxnIhVamNb.huge" target="_blank">spring contacts</a> as you clean the frame.
Unfasten the earpiece speaker
Use a Phillips #000 driver to remove the two screws securing the earpiece speaker:

One 1.8 mm screw

One 2.4 mm screw
Remove the earpiece speaker
Insert the flat end of your spudger between the left edge of the earpiece speaker and the frame.

Pry up until you can grab the speaker with your fingers.

Remove the speaker.

Erinnerung: Reminder During reassembly, insert the speaker at a downward angle so the gasket slides into its recess in the <a href="https://guide-images.cdn.ifixit.com/igi/AWR2dAFIHvUOlWPA.huge" target="_blank">top edge of the frame</a>.