PlayStation 4 Optical Drive Replacement

Gerät: PlayStation 4
Schwierigkeit: Mittel
Geschätzte Dauer: ⏱ 30 min

Follow this guide to replace the optical drive on your Sony Playstation 4.

On 1XXX series models of the PS4, the optical drive daughterboard and the motherboard are paired. If your daughterboard's broken, you'll have to replace the motherboard.

You can replace the the optical drive assembly by itself, but the replacement assembly must be compatible with the your optical drive daughterboard.

Unplug your PS4 before beginning any repairs.

Reparatur anfragen →

Lieber von uns ausführen lassen? Angebot innerhalb eines Werktages.

Werkzeuge

Phillips #0 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
TR8 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Ersatzteile

PlayStation 4 SAA-001 Motherboard and Paired Optical Drive Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Playstation 4 SAB-001 Motherboard and Paired Optical Drive Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
PlayStation 4 SAC-001 Motherboard Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

Flip over the PS4
Flip the PS4 upside-down with the back side facing towards you.
Remove the warranty stickers
Use tweezers to remove the two stickers in the center of the back of the PS4 exposing two case screws.
Remove the plastic screw covers
Use tweezers to carefully remove the plastic screw covers in each corner, exposing two more case screws.
Remove the rear case screws
Remove the four 7.2 mm T8 Torx security screws on the back of the PS4.
Remove the lower case
Use your thumbs to lift the lower case up and off the PS4.

Hinweis: Note The lower case is held into place by plastic clips. You may need to use significant force to release the lower case.
Step 6
Use a pair of tweezers to pull the power supply cable straight out and disconnect the power supply unit from the motherboard.

Hinweis: Note If your connector feels stuck, use a spudger to gently pry the connector out.
Remove the power supply unit
Remove three 9.7 mm-long TR8 Torx security screws.

Remove two 41 mm-long Phillips screws and brackets.
Step 8
Lift the power supply straight up and out of the PS4.

Hinweis: Note The power supply is held firmly in place by prongs on the left side. It may take multiple attempts to remove it.

Erinnerung: Reminder During reassembly, ensure the prongs are aligned, then press the power supply into place.
Remove the Wi-Fi antenna
Use the tip of a spudger to disconnect the antenna cable from the motherboard.
Step 10
Use a pair of tweezers or your fingers to grab the antenna cable and move it out from the cable guides.
Step 11
Use a pair of tweezers or your fingers to thread the antenna cable out from underneath the optical drive cable.
Step 12
Remove the 9.7 mm Torx security screw securing the antenna.
Step 13
Remove the Wi-Fi antenna.
Disconnect the optical drive
Use your fingernail to press down on the metal release lever of the ribbon cable on top of the optical drive.

Use your fingers or a pair of tweezers to disconnect the ribbon cable by pulling on the black tab.

Erinnerung: Reminder You do not need to press the metal lever when inserting the ribbon cable back in. You will hear a click once it is fully inserted.
Step 15
Use your fingernail to press down the metal release lever for the ribbon cable connected to the motherboard.

Use your fingers or a pair of tweezers to disconnect the ribbon cable by pulling on the black tab.

Set the ribbon cable aside for reassembly.

Erinnerung: Reminder You do not need to press the metal lever when inserting the ribbon cable back in. You will hear a click once it is fully inserted.
Step 16
Use your fingers or a pair of tweezers to disconnect the optical drive cable from the motherboard.
Step 17
Use your fingers or a pair of tweezers to remove the optical drive cable from the cable guides that hold it in place.
Remove the optical drive
Remove the four screws securing the optical drive.

Three 9.7 mm Torx screws

One 6.2 mm Phillips screw
Step 19
Lift the optical drive straight up and out of the PS4.
Remove the PCB
Hinweis: Note If you purchased an optical drive with the PCB board and bracket included, skip the remaining steps and begin reassembly.

Remove the three 6.2 mm Phillips screws from the metal bracket.
Step 21
Lift the metal bracket straight up to separate it from the optical drive.
Step 22
Remove the 6.4 mm Phillips screw from the PCB board.
Step 23
Use the tip of a spudger to flip open the ZIF connector locking bar.
Step 24
Pull the ribbon cable straight out of the ZIF connector.
Step 25
Hold the PCB in one hand and the lower ribbon cable in the other.

Gently pull the lower ribbon cable straight out of the socket.
Step 26
Hold the PCB in one hand and the upper ribbon cable in the other.

Pull the upper ribbon cable straight out of the socket.
Step 27
Remove the PCB.

Abschluss

📌To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.