PlayStation 5 Power and Eject Button Board Replacement
Follow this guide to remove and replace the power and eject button board on a PlayStation 5.
Before you begin, completely power down and unplug all cables from your console. Remember to follow general electrostatic discharge (ESD) safety procedures while repairing the console.
Lieber von uns ausführen lassen? Angebot innerhalb eines Werktages.
Werkzeuge
-
Flathead 3/32" or 2.5 mm Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Phillips #0 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
-
TR8 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Ersatzteile
- PlayStation 5 Power & Eject Button Board Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Anleitung
-
Remove the stand screw
If your PlayStation 5 is in its vertical orientation, flip it upside down so the stand is facing up.
Use a coin or a flathead screwdriver to remove the 26.5 mm-long stand screw.
-
-
Remove the vertical stand
Lift straight up to remove the stand.
-
-
Store the stand screw
Insert the screw into the cubby on the bottom of the stand.
-
-
Cap the screw hole
Use a pair of tweezers or your fingernail to remove the cap from the cubby.
Use your finger to press the cap into the screw hole.
-
-
Close the cubby
Twist the stand counterclockwise to close the cubby.
-
-
Remove the horizontal stand
If your PlayStation 5 is in its horizontal orientation, rest it on its face with the charging port facing up.
Lift the stand straight up to remove it.
-
-
Remove the right faceplate
Flip the device over so that the USB and ethernet ports are on the left side from your perspective.
Lift up the corner of the faceplate to unclip it from the case.
-
-
Step 8
While lifting up the corner, slide the faceplate towards the bottom of the device.
Remove the right faceplate.
-
-
Pry up the grille
Insert the flat end of a spudger underneath the grille and into the gap above the fan.
Lift up with the spudger to pry the grille away from the case.
-
-
Remove the grille
Lift the grille away from the case to remove it.
-
-
Remove the fan shroud screws
Use a TR9 Torx Security driver to remove the four screws securing the fan shroud to the case:
Two 23.3 mm-long screws
One 11.4 mm-long screw
One 31 mm-long screw
-
-
Remove the fan shroud
Lift the fan shroud straight up to remove it.
-
-
Remove the wire cover
Insert the flat end of a spudger beneath the black wire cover and into the gap above the fan wires.
Use the spudger to peel up the wire cover until you can grip it with your fingers.
-
-
Step 14
Use your fingers to peel off the wire cover.
-
-
Disconnect the fan
Use your fingers to grip the edges of the fan cable connector, and pull up to disconnect it from the motherboard.
-
-
Remove the fan
Lift the fan up and out of the case to remove it.
-
-
Remove the SSD cover
Use a Phillips screwdriver to remove the 17 mm-long SSD cover screw.
-
-
Step 18
Use your finger to slide the SSD cover towards the top of the device to unclip it from the case.
Remove the SSD cover.
-
-
Remove the optical drive wire
Use your fingers to grip the edges of the optical drive cable connector, and pull up to disconnect it from the motherboard.
-
-
Step 20
Use your fingers to grip the edges of the optical drive cable connector, and pull up to disconnect it from the optical drive.
-
-
Remove the tamper-evident sticker
Use a pair of tweezers to remove the tamper-evident sticker covering the remaining case screw.
-
-
Remove the case screws
Use a TR8 Torx Security driver to remove the eleven screws securing the case:
Six 18.6 mm-long screws
Two 23.3 mm-long screws
Two 43.2 mm-long screws
One 7.3 mm-long screw
-
-
Remove the case
Lift the case straight up to remove it.
-
-
Remove the optical drive ribbon cable
Use the flat end of a spudger to press down on the optical drive connector's metal locking tab.
With the metal tab depressed, use a pair of tweezers to pull the blue pull tab directly away from the connector to disconnect the cable from the optical drive.
-
-
Remove the optical drive
Lift the optical drive away from the device to remove it.
-
-
Remove the optical drive ribbon cable
Use the flat end of a spudger to press down on the optical drive connector's metal locking tab.
With the metal tab depressed, use a pair of tweezers to pull the blue pull tab directly away from the connector to disconnect the cable from the motherboard.
-
-
Remove the power and eject button ribbon cable
Use a pair of tweezers to pull the blue pull tab directly away from the connector to disconnect the power and eject button ribbon cable.
-
-
Remove the LED ribbon cable
Use a pair of tweezers to pull the blue pull tab directly away from the connector to disconnect the LED ribbon cable.
-
-
Remove the antenna wires
Use a pair of tweezers to grip the white Wi-Fi antenna wire at its metal base, as close to the connector as possible.
Lift the wire's connector straight up to disconnect it from the motherboard.
Repeat for the black Wi-Fi antenna wire.
-
-
Step 30
Use a pair of tweezers to grip the black or blue power supply antenna wire at its metal base, as close to the connector as possible.
Lift the wire's connector straight up to disconnect it from the motherboard.
Repeat for the white power supply antenna wire.
-
-
Remove the white stickers
Use a pair of tweezers to peel back the white sticker holding the antenna wires to the top shield plate.
Remove the antenna wires from underneath the sticker.
Press the white sticker back down onto the top shield plate so it can be reused.
-
-
Step 32
Repeat the previous step to peel back the four remaining stickers.
-
-
Step 33
Use a pair of tweezers to peel back the white sticker holding the LED ribbon cable to the heat sink.
Remove the LED ribbon cable from underneath the sticker.
Press the white sticker back down onto the heat sink so it can be reused.
-
-
Remove the top shield plate screws
Use a TR8 Torx Security driver to remove the forty-two screws securing the top shield plate:
Forty-one 7.3 mm-long screws
One 43.2 mm-long screw
-
-
Remove the top shield plate
Lift the top shield plate off of the motherboard to remove it.
-
-
Disconnect the USB board
Use your finger to depress the metal locking tab on the USB board cable's board connector.
With the metal tab depressed, place the flat end of a spudger against the insulating foam pad on the ribbon cable and pull it directly away from the connector to disconnect it.
-
-
Remove the left faceplate
Lift up the corner of the faceplate with the PlayStation logo to unclip it from the case.
-
-
Step 38
While lifting up the corner, slide the faceplate towards the bottom of the device.
Remove the left faceplate.
-
-
Remove the screws
Use a TR8 Torx Security driver to remove the two 29.4 mm-long screws securing the case to the motherboard and heat sink assembly.
-
-
Remove the case
Lift the front edge of the case off of the motherboard and heat sink assembly.
With the front edge elevated, push the case back, away from the motherboard and heat sink assembly, to maneuver the charging port out of its slot in the case.
Remove the case.
-
-
Remove the middle panel
Lift up to remove the middle panel from the case.
-
-
Remove the screws
Use a Phillips screwdriver to remove the two 6.5 mm-long screws securing the power and eject button board to the middle panel.
-
-
Remove the power and eject button board
Use a pair of tweezers to remove the power and eject button board from the middle panel.
-
-
Step 44
Use a pair of tweezers to pull the blue pull tab directly away from the connector to disconnect the power and eject button ribbon cable.
-
Abschluss
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our PlayStation 5 Answers community for help.