Samsung Galaxy S24 Back Cover Replacement
Use this guide to replace the back cover (aka back glass) on your Samsung Galaxy S24.
Note: Retaining water resistance after the repair will depend on how well you reapply the back cover adhesive, but your device will lose its IP (Ingress Protection) rating.
Lieber von uns ausführen lassen? Angebot innerhalb eines Werktages.
Werkzeuge
-
Hair Dryer Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Heat Gun Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
iFixit Opening Picks (Set of 6) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
iOpener Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
- Isopropyl Alcohol (90% or Greater) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Suction Handle Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Ersatzteile
-
Samsung Galaxy S24 Back Glass Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Samsung Galaxy S24 Rear Cover Adhesive Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Anleitung
-
Prepare your phone for disassembly
Completely power off your phone and unplug all cables.
-
-
Heat the right edge
Heat an iOpener and apply it to the right edge of the back cover for two minutes.
-
-
Insert an opening pick
Apply a suction handle to the back cover, as close to the center of the right edge as possible.
Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.
Insert an opening pick into the gap.
-
-
Separate the right adhesive
Slide your opening pick along the right edge between the back cover and the frame to slice through the adhesive.
Leave your opening pick in the bottom right corner to keep the adhesive from resealing.
-
-
Heat the bottom edge
Reheat your iOpener and apply it to the bottom of the back cover for two minutes.
-
-
Separate the corner adhesive
Rotate the opening pick around the bottom right corner to separate the adhesive.
-
-
Separate the bottom adhesive
Insert a second opening pick to the left of the first one and slide it along the bottom edge to slice through the adhesive.
Leave your opening pick in the bottom left edge to prevent the adhesive from resealing.
-
-
Heat the left edge
Reheat your iOpener and apply it to the left side of the back cover for two minutes.
-
-
Separate the corner adhesive
Rotate the opening pick around the bottom left corner to separate the adhesive.
-
-
Separate the left adhesive
Insert a third opening pick above the last one and slide it along the left edge to slice through the adhesive.
Leave your opening pick in the top left corner to prevent the adhesive from resealing.
-
-
Heat the top edge
Reheat your iOpener and apply it to the top of the back cover for two minutes.
-
-
Separate the corner adhesive
Rotate the opening pick around the top left corner to separate the adhesive.
-
-
Separate the top adhesive
Insert a fourth opening pick in the top left corner at the same depth and slide it along the top edge and around the top right corner to slice through the adhesive.
-
-
Separate the flash adhesive
Insert a fifth opening pick directly above the camera flash cutout.
Insert the opening pick under the top of the back cover until you feel it start to snag on the flash adhesive.
Insert the pick deeper into the phone until you feel the adhesive completely separate from the back cover.
-
-
Remove the back cover
Pick up the back cover by its edges and remove it from the phone.
Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat and isopropyl alcohol (90% or greater) if you're having trouble removing the adhesive.
If you're using custom-cut adhesives, follow this guide.
If you're using double-sided tape, follow this guide.
-
Abschluss
Compare your new replacement part to the original part—be sure to transfer remaining components and remove adhesive backings from the new part before installing.
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Samsung Galaxy S24 Answers Community for troubleshooting help.