Samsung Galaxy S24 Screen and Battery Assembly Replacement

Werkzeuge

• Hair Dryer Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Heat Gun Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• iFixit Opening Picks (Set of 6) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• iOpener Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Isopropyl Alcohol (90% or Greater) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Phillips #0 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• SIM Card Eject Tool Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
• Suction Handle Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

1. Prepare your phone for disassembly

   • 
   • 

   Completely power off your phone and unplug all cables.

2. Heat the right edge

   • 

   Heat an iOpener and apply it to the right edge of the back cover for two minutes.

3. Insert an opening pick

   • 
   • 
   • 

   Apply a suction handle to the back cover, as close to the center of the right edge as possible.

   Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.

   Insert an opening pick into the gap.

4. Separate the right adhesive

   • 
   • 
   • 

   Slide your opening pick along the right edge between the back cover and the frame to slice through the adhesive.

   Leave your opening pick in the bottom right corner to keep the adhesive from resealing.

5. Heat the bottom edge

   • 

   Reheat your iOpener and apply it to the bottom of the back cover for two minutes.

6. Separate the corner adhesive

   • 
   • 

   Rotate the opening pick around the bottom right corner to separate the adhesive.

7. Separate the bottom adhesive

   • 
   • 

   Insert a second opening pick to the left of the first one and slide it along the bottom edge to slice through the adhesive.

   Leave your opening pick in the bottom left edge to prevent the adhesive from resealing.

8. Heat the left edge

   • 

   Reheat your iOpener and apply it to the left side of the back cover for two minutes.

9. Separate the corner adhesive

   • 
   • 

   Rotate the opening pick around the bottom left corner to separate the adhesive.

10. Separate the left adhesive

    • 
    • 

    Insert a third opening pick above the last one and slide it along the left edge to slice through the adhesive.

    Leave your opening pick in the top left corner to prevent the adhesive from resealing.

11. Heat the top edge

    • 

    Reheat your iOpener and apply it to the top of the back cover for two minutes.

12. Separate the corner adhesive

    • 
    • 

    Rotate the opening pick around the top left corner to separate the adhesive.

13. Separate the top adhesive

    • 
    • 
    • 

    Insert a fourth opening pick in the top left corner at the same depth and slide it along the top edge and around the top right corner to slice through the adhesive.

14. Separate the flash adhesive

    • 
    • 

    Insert a fifth opening pick directly above the camera flash cutout.

    Insert the opening pick under the top of the back cover until you feel it start to snag on the flash adhesive.

    Insert the pick deeper into the phone until you feel the adhesive completely separate from the back cover.

15. Remove the back cover

    • 
    • 

    Pick up the back cover by its edges and remove it from the phone.

    Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat and isopropyl alcohol (90% or greater) if you're having trouble removing the adhesive.

    If you're using custom-cut adhesives, follow this guide.

    If you're using double-sided tape, follow this guide.

16. Disconnect the wireless charging coil

    • 
    • 

    Use the point of your spudger to pry up and disconnect the wireless charging coil press connector from the motherboard.

17. Remove the wireless charging coil and loudspeaker screws

    • 
    • 
    • 

    Use a Phillips screwdriver to remove the thirteen 3.5 mm‑long screws securing the wireless charging coil and the loudspeaker:

    Six screws securing the wireless charging coil

    Seven screws securing the loudspeaker

18. Remove the wireless charging coil and loudspeaker

    • 
    • 

    Insert the point of a spudger in the notch located on the left edge of the loudspeaker assembly.

    Pry up the loudspeaker to release its clips.

19. Step 19

    • 
    • 
    • 

    Use your fingernail or the flat end of a spudger to pry up the wireless charging coil and loudspeaker assembly away from the frame.

    Remove the wireless charging coil and loudspeaker from your phone.

20. Remove the SIM card tray

    • 
    • 
    • 

    Insert a SIM card eject tool, bit, or a straightened paperclip into the hole on the SIM tray at the bottom of the phone.

    Press in firmly to eject the tray and remove it.

21. Disconnect the battery

    • 
    • 

    Insert the flat end of a spudger under the battery cable press connector (located on the motherboard) and pry up to disconnect it.

22. Disconnect the earpiece speaker

    • 
    • 

    Insert the tip of a spudger underneath the left side of the earpiece speaker connector and pry up to disconnect it.

23. Remove the earpiece speaker screws

    • 
    • 

    Use a Phillips screwdriver to remove the five 3.5 mm‑long screws securing the earpiece speaker.

24. Remove the earpiece speaker

    • 
    • 
    • 

    Insert the flat end of a spudger underneath the bottom of the earpiece speaker assembly and pry up to free it from the chassis.

    Remove the earpiece speaker.

25. Disconnect the interconnect cables

    • 
    • 
    • 

    Insert the point of a spudger under the secondary interconnect cable press connector labeled "MAIN" (located on the bottom right corner of the motherboard) and pry up to disconnect it.

    Repeat this process for the primary interconnect cable connector.

26. Step 26

    • 
    • 

    Repeat this process to disconnect the display and 5G mmWave cable press connectors located on the bottom left edge of the motherboard.

27. Step 27

    • 
    • 
    • 

    Repeat this process to disconnect the two interconnect cable press connectors located on the daughterboard, and the display cable connector to the left of the daughterboard.

28. Remove the interconnect cables

    • 
    • 
    • 

    Remove the two interconnect cables and the display cable from your phone.

29. Disconnect the mmWave antenna

    • 
    • 

    Insert the point of a spudger under the top left corner of the mmWave antenna press connector located on the right edge of the motherboard and pry up to disconnect it.

30. Disconnect the front camera

    • 
    • 

    Insert the flat end of a spudger under the front camera press connector and pry up to disconnect it.

31. Remove the motherboard

    • 
    • 

    Use a Phillips screwdriver to remove the two 3.4 mm‑long screws securing the rear cameras and motherboard.

32. Step 32

    • 
    • 

    Insert the flat end of a spudger under the top edge of the motherboard and pry up until it is touching the front camera and mmWave antenna cables.

33. Step 33

    • 
    • 
    • 

    Move the front camera and mmWave antenna cables out of the way of the motherboard.

    Completely lift the motherboard until it's free and remove it from your phone.

34. Heat the front camera

    • 

    Use a hair dryer or a heat gun to heat the front camera for 90 seconds.

35. Remove the front camera

    • 
    • 
    • 

    Use the flat end of your spudger to pry the front camera from its recess in the frame enough to grip it with your fingers.

    Remove the front camera.

36. Remove the antenna

    • 
    • 
    • 

    Insert the tip of your spudger in the notch between the bottom edge of the antenna and the frame.

    Pry up and lift the antenna to separate the adhesive securing it.

    Use your fingers to pull the antenna out of the frame, separating any remaining adhesive from it.

37. Step 37

    • 
    • 

    Use a Phillips screwdriver to remove the two 2.5 mm‑long screws securing the 5G mmWave antenna.

38. Remove the mmWave antenna

    • 
    • 
    • 

    Insert one arm of a pair of angled tweezers into the bottom screw hole on the 5G mmWave antenna bracket.

    Pry up with the tweezers and lift the antenna bracket out of its recess enough until you can grip it with your fingers.

39. Step 39

    • 
    • 

    Lift the 5G mmWave antenna out of its recess to separate the adhesive securing it.

    Remove the 5G mmWave antenna.

40. Unscrew the daughterboard

    • 
    • 

    Use a Phillips screwdriver to remove the two 3.4 mm‑long screws securing the daughterboard.

41. Remove the USB-C port and daughterboard

    • 
    • 
    • 

    Use the point of a spudger to pry up the top right corner of the daughterboard and unclip it from the frame.

    Remove the daughterboard.

42. Step 42

    • 

    You're now left with the screen and battery assembly.

Abschluss

Compare your new replacement part to the original part—be sure to transfer remaining components and remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Samsung Galaxy S24 Answers Community for troubleshooting help.