Samsung Galaxy S24 Ultra Battery Replacement

Gerät: Samsung Galaxy S24 Ultra
Schwierigkeit: Mittel
Geschätzte Dauer: ⏱ 45 min

Follow this guide to replace a dead or worn-out battery in your Samsung Galaxy S24 Ultra.

This guide is for the battery only. If you're replacing the screen and battery assembly (the frame, screen, and battery as one piece), follow this guide instead.

Reparatur anfragen →

Lieber von uns ausführen lassen? Angebot innerhalb eines Werktages.

Werkzeuge

Coffee Filters or a lint-free cloth Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Hair Dryer Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Heat Gun Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
iFixit Opening Picks (Set of 6) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
iOpener Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Isopropyl Alcohol (90% or Greater) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Phillips #00 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
Suction Handle Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Ersatzteile

Samsung Galaxy S24 Ultra Battery Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Samsung Galaxy S24 Ultra Battery Adhesive Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

Prepare your phone for disassembly
Vorsicht: Caution Allow your phone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard. If your battery is swollen, take appropriate precautions.

Unplug any cables from your phone.

Hold the side key and the volume down button, then select "Power off" to turn off your phone.
Heat the right edge
Heat an iOpener and apply it to the right edge of the back cover for two minutes.

Hinweis: Note You may use a <a href="https://www.ifixit.com/Guide/How+to+Use+a+Hair+Dryer+to+Soften+Adhesive/157348" target="_blank">hair dryer</a>, <a href="https://www.ifixit.com/Guide/How+to+Use+a+Heat+Gun+to+Soften+Adhesive/151116" target="_blank">heat gun</a>, or hot plate instead, but be careful not to overheat the phone—the display and internal battery are susceptible to heat damage.
Insert an opening pick
Apply a suction handle to the back cover, as close to the center of the right edge as possible.

Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.

Hinweis: Note If you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the <a href="https://www.ifixit.com/Guide/iOpener+Heating/25705" target="_blank">iOpener instructions</a> to avoid overheating.

Insert an opening pick into the gap.
Separate the right adhesive
Slide the pick back and forth along the right edge to separate the adhesive.

Leave the pick inserted near the bottom right corner to prevent the adhesive from resealing.
Heat the bottom edge
Apply a heated iOpener to the bottom edge of the back cover for two minutes.
Separate the bottom adhesive
Insert a second opening pick next to the first one, near the bottom of the right edge.

Rotate the opening pick around the bottom right corner to separate the adhesive.
Step 7
Slide the opening pick along the bottom edge to separate the adhesive.

Leave the pick inserted near the bottom left corner to prevent the adhesive from resealing.
Heat the left edge
Apply a heated iOpener to the left edge of the back cover for two minutes.
Separate the left adhesive
Insert a third opening pick next to the second one, near the left side of the bottom edge.

Rotate the opening pick around the bottom left corner to separate the adhesive.
Step 10
Slide your opening pick along the left edge to separate the adhesive, stopping before you reach the power button.

Vorsicht: Caution Do not insert the pick more than 4 mm to avoid damaging the <a href="https://guide-images.cdn.ifixit.com/igi/FwyD52BTVgTAFUxd.full" target="_blank">antenna cable</a>.

Leave the pick inserted near the power button to prevent the adhesive from resealing.
Heat the top edge
Apply a heated iOpener to the top edge of the back cover for two minutes.
Separate the top adhesive
Insert an opening pick in the gap at the top of the right edge.

Rotate the opening pick around the top right corner to separate the adhesive.
Step 13
Slide the pick along the top edge to separate the adhesive.

Vorsicht: Caution Do not insert the pick more than 4 mm to avoid damaging the sensor or camera near the top edge.
Separate the remaining adhesive
Slide the pick around the top left corner and down the left edge to separate the remaining adhesive.

Vorsicht: Caution Do not insert the pick more than 4 mm to avoid damaging the cameras.
Remove the back cover
Grab and remove the back cover.

Hinweis: Note If your cover is still sticking to the frame, slide an opening pick around the edges to separate any adhesive that may have resealed.

Erinnerung: Reminder During reassembly:

Hinweis: Note This is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.

Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat if you're having trouble separating the adhesive.

If you're using custom-cut adhesives, follow this guide.

If you're using double-sided tape, follow this guide.
Disconnect the wireless charging coil
Use a spudger to pry up and disconnect the wireless charging coil press connector from the motherboard.

Hinweis: Note There's an arrow printed on the board near each press connector that indicates the recommended prying location. Only pry in this location for each press connector to avoid dislodging surface-mounted components.

Erinnerung: Reminder To reconnect press connectors, align the connector carefully over its socket and press down with your fingertip—first on one side, then the other—until it clicks into place. Don't try to force the connector into place. If you're having trouble, reposition it and try again.
Remove the wireless charging coil and loudspeaker screws
Use a Phillips screwdriver to remove the ten 3.5 mm‑long screws securing the wireless charging coil and the loudspeaker:

Four screws securing the wireless charging coil

Six screws securing the loudspeaker
Separate the coil adhesive
Use a spudger to gently pry up a corner of the tab of the wireless charging coil that's adhered to the right edge of the frame.
Step 19
Use an opening pick to separate the tab from the frame.
Remove the wireless charging coil and loudspeaker
Insert the point of a spudger into the gap between the right edge of the loudspeaker and the frame.

Hinweis: Note There's an arrow engraved in the loudspeaker to indicate the recommended prying location.

Pry up to unclip the loudspeaker from the frame.
Step 21
Remove the wireless charging coil and loudspeaker from the frame.

Erinnerung: Reminder During reassembly, press around the edges of the loudspeaker to clip it to the frame before reinserting the screws.
Disconnect the battery
Use a spudger to pry up and disconnect the battery press connector.
Disconnect the interconnect cables
Use a spudger to pry up and disconnect both interconnect cable press connectors from the motherboard.
Step 24
Use a spudger to pry up and disconnect both interconnect cable press connectors from the daughterboard.
Remove the interconnect cables
Grab and remove the interconnect cables from the phone.
Remove the display cable
Use a spudger to pry up and disconnect the display cable press connector from the motherboard.
Step 27
Use a spudger to pry up and disconnect the display cable press connector from the daughterboard.

Grab and remove the display cable.
Move the lower antenna cable
Use a spudger to pry up and disconnect the lower antenna cable press connector from the motherboard.

Move the lower antenna cable so it is out of the way of the battery.
Peel back the pull tab
Vorsicht: Caution Be very careful not to bend, crease, or puncture the battery during the next few steps. A damaged battery can leak dangerous chemicals and catch fire.

Peel the battery pull tab away from the battery, towards the left edge of the phone.

Hinweis: Note If you're having trouble getting the pull tab up, use and opening pick or other thin plastic tool at a low angle to peel up a corner. Never use a metal tool on battery, and never press into the battery.
Step 30
Separate the small, clear tabs above and below the blue part of the pull tab from the rest of the pull tab.

Bend these small tabs away from the battery to make sure they stay clear of the battery.

Hinweis: Note If these tabs aren't separated, you won't be able to lift the battery in the next step. You can tape these tabs to the side of the phone or the screen to keep them out of the way.

Your device may have two tabs on the bottom edge of the battery. These are designed to tear away during the next step, but if you have trouble removing the battery, you can carefully peel these tabs up as well.
Remove the battery
Hinweis: Note This battery is held by a piece of double-sided adhesive film that is doubled under the battery. When you lift the battery by the pull tab, the left edge will come up, but the right edge will not. You'll remove the remaining film and the battery in the next step.

With one hand firmly holding down the frame of the phone, use firm, steady force to lift the blue pull tab straight up until the battery separates from the bottom layer of adhesive film.

Hinweis: Note If you're having trouble, apply <strong>1-2 drops</strong> of high‑concentration (90% or more) isopropyl alcohol to the <a href="https://guide-images.cdn.ifixit.com/igi/hLsCusBLdvfEtefM.full" target="_blank">left edge of the battery</a>. Raise the left edge of the phone to let the alcohol flow under the battery and wait one minute for it to soften the adhesive.

Lay the battery over the right edge of your phone.

Vorsicht: Caution Be careful not to bend the battery on the right edge of the phone frame. You may need to peel up some of the bottom layer of adhesive film by pulling the battery up before laying it over the edge of the phone.
Step 32
Peel up the remaining film from the frame.

Remove the battery.

If you used isopropyl alcohol, wait ten minutes before installing the new battery to allow the alcohol to completely evaporate.

Abschluss

To reassemble your device, follow these instructions in reverse order.

For optimal performance, calibrate your newly installed battery after reassembling your phone.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Take your e-waste to an R2 or e-Stewards certified recycler.

Werkzeuge

Ersatzteile

Anleitung

Prepare your phone for disassembly

Heat the right edge

Insert an opening pick

Separate the right adhesive

Heat the bottom edge

Separate the bottom adhesive

Step 7

Heat the left edge

Separate the left adhesive

Step 10

Heat the top edge

Separate the top adhesive

Step 13

Separate the remaining adhesive

Remove the back cover

Disconnect the wireless charging coil

Remove the wireless charging coil and loudspeaker screws

Separate the coil adhesive

Step 19

Remove the wireless charging coil and loudspeaker

Step 21

Disconnect the battery

Disconnect the interconnect cables

Step 24

Remove the interconnect cables

Remove the display cable

Step 27

Move the lower antenna cable

Peel back the pull tab

Step 30

Remove the battery

Step 32

Abschluss