Samsung Galaxy S24 Ultra Front Camera Replacement
Use this guide to replace the front camera in your Samsung Galaxy S24 Ultra.
Lieber von uns ausführen lassen? Angebot innerhalb eines Werktages.
Werkzeuge
-
Coffee Filters or a lint-free cloth Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Hair Dryer Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Heat Gun Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
iFixit Opening Picks (Set of 6) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
iOpener Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
- Isopropyl Alcohol (90% or Greater) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Phillips #00 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
SIM Card Eject Tool Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
-
Suction Handle Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Anleitung
-
Prepare your phone for disassembly
Unplug any cables from your phone.
Hold the side key and the volume down button, then select "Power off" to turn off your phone.
-
-
Heat the right edge
Heat an iOpener and apply it to the right edge of the back cover for two minutes.
-
-
Insert an opening pick
Apply a suction handle to the back cover, as close to the center of the right edge as possible.
Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.
Insert an opening pick into the gap.
-
-
Separate the right adhesive
Slide the pick back and forth along the right edge to separate the adhesive.
Leave the pick inserted near the bottom right corner to prevent the adhesive from resealing.
-
-
Heat the bottom edge
Apply a heated iOpener to the bottom edge of the back cover for two minutes.
-
-
Separate the bottom adhesive
Insert a second opening pick next to the first one, near the bottom of the right edge.
Rotate the opening pick around the bottom right corner to separate the adhesive.
-
-
Step 7
Slide the opening pick along the bottom edge to separate the adhesive.
Leave the pick inserted near the bottom left corner to prevent the adhesive from resealing.
-
-
Heat the left edge
Apply a heated iOpener to the left edge of the back cover for two minutes.
-
-
Separate the left adhesive
Insert a third opening pick next to the second one, near the left side of the bottom edge.
Rotate the opening pick around the bottom left corner to separate the adhesive.
-
-
Step 10
Slide your opening pick along the left edge to separate the adhesive, stopping before you reach the power button.
Leave the pick inserted near the power button to prevent the adhesive from resealing.
-
-
Heat the top edge
Apply a heated iOpener to the top edge of the back cover for two minutes.
-
-
Separate the top adhesive
Insert an opening pick in the gap at the top of the right edge.
Rotate the opening pick around the top right corner to separate the adhesive.
-
-
Step 13
Slide the pick along the top edge to separate the adhesive.
-
-
Separate the remaining adhesive
Slide the pick around the top left corner and down the left edge to separate the remaining adhesive.
-
-
Remove the back cover
Grab and remove the back cover.
Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat if you're having trouble separating the adhesive.
If you're using custom-cut adhesives, follow this guide.
If you're using double-sided tape, follow this guide.
-
-
Disconnect the wireless charging coil
Use a spudger to pry up and disconnect the wireless charging coil press connector from the motherboard.
-
-
Remove the wireless charging coil and loudspeaker screws
Use a Phillips screwdriver to remove the ten 3.5 mm‑long screws securing the wireless charging coil and the loudspeaker:
Four screws securing the wireless charging coil
Six screws securing the loudspeaker
-
-
Separate the coil adhesive
Use a spudger to gently pry up a corner of the tab of the wireless charging coil that's adhered to the right edge of the frame.
-
-
Step 19
Use an opening pick to separate the tab from the frame.
-
-
Remove the wireless charging coil and loudspeaker
Insert the point of a spudger into the gap between the right edge of the loudspeaker and the frame.
Pry up to unclip the loudspeaker from the frame.
-
-
Step 21
Remove the wireless charging coil and loudspeaker from the frame.
-
-
Disconnect the battery
Use a spudger to pry up and disconnect the battery press connector.
-
-
Disconnect the earpiece speaker
Use a spudger to pry up and disconnect the earpiece speaker press connector.
-
-
Remove the earpiece speaker screws
Use a Phillips screwdriver to remove the five 3.5 mm‑long screws securing the earpiece speaker.
-
-
Remove the earpiece speaker
Insert the pointed end of a spudger under the bottom edge of the earpiece speaker, under the engraved arrow.
Pry up with the spudger to unclip the speaker and remove it.
-
-
Disconnect the front camera
Use a spudger to pry up and disconnect the front camera press connector.
-
-
Heat the front camera adhesive
Flip the phone over so the screen is facing up.
Heat an iOpener and apply it to the top edge of the screen for two minutes to loosen the front camera adhesive.
Flip the phone back over so the back of the front camera is accessible.
-
-
Pry up the front camera
Use the flat end of a spudger to pry the front camera from its recess in the frame.
-
-
Remove the front camera
Lift and remove the front camera.
-
Abschluss
To reassemble your device, follow these instructions in reverse order.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.
Take your e-waste to an R2 or e-Stewards certified recycler.