Samsung Galaxy S24 Ultra Screen and Battery Assembly Replacement

Werkzeuge

• Angled Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Coffee Filters or a lint-free cloth Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Hair Dryer Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Heat Gun Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• iFixit Opening Picks (Set of 6) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• iOpener Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Isopropyl Alcohol (90% or Greater) Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Phillips #00 Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• SIM Card Eject Tool Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
• Suction Handle Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

1. Prepare your phone for disassembly

   • 
   • 

   Unplug any cables from your phone.

   Hold the side key and the volume down button, then select "Power off" to turn off your phone.

2. Heat the right edge

   • 

   Heat an iOpener and apply it to the right edge of the back cover for two minutes.

3. Insert an opening pick

   • 
   • 
   • 

   Apply a suction handle to the back cover, as close to the center of the right edge as possible.

   Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.

   Insert an opening pick into the gap.

4. Separate the right adhesive

   • 
   • 
   • 

   Slide the pick back and forth along the right edge to separate the adhesive.

   Leave the pick inserted near the bottom right corner to prevent the adhesive from resealing.

5. Heat the bottom edge

   • 

   Apply a heated iOpener to the bottom edge of the back cover for two minutes.

6. Separate the bottom adhesive

   • 
   • 
   • 

   Insert a second opening pick next to the first one, near the bottom of the right edge.

   Rotate the opening pick around the bottom right corner to separate the adhesive.

7. Step 7

   • 
   • 

   Slide the opening pick along the bottom edge to separate the adhesive.

   Leave the pick inserted near the bottom left corner to prevent the adhesive from resealing.

8. Heat the left edge

   • 

   Apply a heated iOpener to the left edge of the back cover for two minutes.

9. Separate the left adhesive

   • 
   • 
   • 

   Insert a third opening pick next to the second one, near the left side of the bottom edge.

   Rotate the opening pick around the bottom left corner to separate the adhesive.

10. Step 10

    • 
    • 

    Slide your opening pick along the left edge to separate the adhesive, stopping before you reach the power button.

    Leave the pick inserted near the power button to prevent the adhesive from resealing.

11. Heat the top edge

    • 

    Apply a heated iOpener to the top edge of the back cover for two minutes.

12. Separate the top adhesive

    • 
    • 
    • 

    Insert an opening pick in the gap at the top of the right edge.

    Rotate the opening pick around the top right corner to separate the adhesive.

13. Step 13

    • 
    • 

    Slide the pick along the top edge to separate the adhesive.

14. Separate the remaining adhesive

    • 
    • 
    • 

    Slide the pick around the top left corner and down the left edge to separate the remaining adhesive.

15. Remove the back cover

    • 
    • 

    Grab and remove the back cover.

    Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat if you're having trouble separating the adhesive.

    If you're using custom-cut adhesives, follow this guide.

    If you're using double-sided tape, follow this guide.

16. Disconnect the wireless charging coil

    • 
    • 

    Use a spudger to pry up and disconnect the wireless charging coil press connector from the motherboard.

17. Remove the wireless charging coil and loudspeaker screws

    • 
    • 

    Use a Phillips screwdriver to remove the ten 3.5 mm‑long screws securing the wireless charging coil and the loudspeaker:

    Four screws securing the wireless charging coil

    Six screws securing the loudspeaker

18. Separate the coil adhesive

    • 
    • 

    Use a spudger to gently pry up a corner of the tab of the wireless charging coil that's adhered to the right edge of the frame.

19. Step 19

    • 
    • 

    Use an opening pick to separate the tab from the frame.

20. Remove the wireless charging coil and loudspeaker

    • 
    • 

    Insert the point of a spudger into the gap between the right edge of the loudspeaker and the frame.

    Pry up to unclip the loudspeaker from the frame.

21. Step 21

    • 
    • 

    Remove the wireless charging coil and loudspeaker from the frame.

22. Disconnect the battery

    • 
    • 

    Use a spudger to pry up and disconnect the battery press connector.

23. Disconnect the interconnect cables

    • 
    • 
    • 

    Use a spudger to pry up and disconnect both interconnect cable press connectors from the motherboard.

24. Step 24

    • 
    • 
    • 

    Use a spudger to pry up and disconnect both interconnect cable press connectors from the daughterboard.

25. Remove the interconnect cables

    • 
    • 

    Grab and remove the interconnect cables from the phone.

26. Remove the SIM card tray

    • 
    • 
    • 

    Insert a SIM eject tool, bit, or straightened paper clip into the SIM card tray hole on the bottom edge of the phone.

    Press the SIM eject tool into the SIM card tray hole to eject the SIM card tray.

    Remove the SIM card tray.

27. Remove the daughterboard screws

    • 

    Use a Phillips screwdriver to remove the three 3.5 mm‑long screws securing the daughterboard.

28. Remove the daughterboard

    • 
    • 
    • 

    Use the point of a spudger to pry up the top left corner of the daughterboard.

    Remove the daughterboard.

29. Disconnect the earpiece speaker

    • 
    • 

    Use a spudger to pry up and disconnect the earpiece speaker press connector.

30. Remove the earpiece speaker screws

    • 

    Use a Phillips screwdriver to remove the five 3.5 mm‑long screws securing the earpiece speaker.

31. Remove the earpiece speaker

    • 
    • 
    • 

    Insert the pointed end of a spudger under the bottom edge of the earpiece speaker, under the engraved arrow.

    Pry up with the spudger to unclip the speaker and remove it.

32. Remove the display cable

    • 
    • 

    Use a spudger to pry up and disconnect the display cable press connector from the motherboard.

33. Step 33

    • 
    • 
    • 

    Use a spudger to pry up and disconnect the display cable press connector from the daughterboard.

    Remove the display cable.

34. Disconnect the lower antenna

    • 
    • 

    Use a spudger to pry up and disconnect the lower antenna press connector from the motherboard.

35. Disconnect the stylus port

    • 
    • 

    Use a spudger to pry up and disconnect the stylus port press connector from the motherboard.

36. Disconnect the upper antenna

    • 
    • 

    Use a spudger to pry up and disconnect the upper antenna press connector from the motherboard.

37. Disconnect the fingerprint scanner

    • 
    • 

    Use a spudger to pry up and disconnect the fingerprint scanner press connector from the motherboard.

38. Disconnect the front camera

    • 
    • 

    Use a spudger to pry up and disconnect the front camera press connector from the motherboard.

39. Remove the motherboard screws

    • 

    Use a Phillips screwdriver to remove the two screws securing the motherboard:

    One 4.0 mm-long screw to the left of the top camera.

    One 3.5 mm-long screw to the left of the bottom camera.

40. Remove the motherboard

    • 
    • 
    • 

    Use your finger or a spudger to lift the top of the motherboard.

    Remove the motherboard.

41. Remove the stylus

    • 
    • 
    • 

    Push the button at the base of the stylus.

    Remove the stylus.

42. Remove the lower antenna screws

    • 

    Use a Phillips driver to remove the two 2.5 mm‑long screws securing the lower antenna.

43. Remove the lower antenna

    • 
    • 

    Insert one arm of a pair of angled tweezers or a SIM eject tool into the bottom screw hole on the lower antenna bracket.

    Pry up and lift the antenna bracket out of its recess until you can grip it with your fingers.

44. Step 44

    • 
    • 

    Lift and remove the lower antenna.

45. Remove the upper antenna

    • 
    • 

    Insert the flat end of a spudger under the upper antenna cable, between the antenna and the frame.

    Twist the spudger to lift the antenna free of its adhesive.

46. Step 46

    • 
    • 

    Lift and remove the upper antenna.

47. Remove the front camera

    • 

    Flip over the phone so the screen is facing up.

    Heat an iOpener and apply it to the top edge of the screen for two minutes to loosen the front camera adhesive.

    Flip the phone back over so the back of the front camera is accessible.

48. Step 48

    • 
    • 
    • 

    Use the flat end of a spudger to pry the front camera from its recess in the frame.

    Lift and remove the front camera.

49. Only the screen and battery assembly remains

    • 

    You're now left with the screen and battery assembly.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Take your e-waste to an R2 or e-Stewards certified recycler.