Xbox One X Fan Replacement

Werkzeuge

• ESD Safe Blunt Nose Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
• TR10 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• TR8 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Ersatzteile

• Xbox One X Fan Assembly Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

1. Remove the sticker

   • 
   • 

   Use blunt tweezers to peel off the sticker covering the right-side screw on the back of the console.

2. Remove the external screws

   • 

   Use a T10 Torx screwdriver to remove the two 12.6 mm–long screws located on the back of the console.

3. Slide the upper case horizontally

   • 
   • 

   Rotate the console 90 degrees.

   Pull the front of the upper plastic case horizontally toward the front of the console until it comes to a stop. This slides the clips out of the slots on the upper plastic case.

4. Lift the upper case off the lower case

   • 
   • 

   Rotate the console 90 degrees so that the back is facing you.

   Lift up the left side of the upper plastic case (as viewed from the back of the console), stopping when it won’t lift any further.

5. Step 5

   • 
   • 
   • 

   While continuing to hold the left side of the upper plastic case, push up on the right side to move the right-side screw boss out of the way.

   Swing the upper plastic case open to 75 degrees.

6. Step 6

   • 
   • 

   Push the upper plastic case down and away from the console to remove it completely.

7. Disconnect the ribbon cable

   • 
   • 
   • 

   Use the pointed end of a spudger, an opening tool, or your fingernail to flip down the small, hinged locking flap on the ribbon cable ZIF connector on the front circuit board.

8. Disconnect the ribbon cable

   • 

   Use blunt tweezers to pull the ribbon cable down out of the connector.

9. Remove the front circuit board screws

   • 

   Use a T8 Torx screwdriver to remove the three 13.3 mm screws securing the front circuit board to the upper metal case.

10. Remove the front circuit board

    • 
    • 

    Pull the front circuit board straight out away from the upper metal case and set it aside.

11. Remove the upper metal case screws

    • 

    Use a T10 Torx screwdriver to remove the six 47.7 mm screws securing the upper metal case to the lower plastic case.

    Use a T8 Torx screwdriver to remove the two 7.5 mm screws securing the press connector to the upper metal case.

12. Detach the press connector

    • 
    • 

    Insert the flat end of a spudger underneath the press connector on the side opposite of the ribbon cable.

    Use the spudger to lift the press connector up and away from the upper metal case.

13. Remove the lower plastic case

    • 
    • 
    • 

    Flip the console over.

    Lift the lower plastic case up from the metal case and set it aside.

14. Remove the lower metal case screws

    • 

    Remove the two T10 Torx screws securing the lower metal case:

    One 7.7 mm screw

    One 11.4 mm screw

15. Remove the lower metal case

    • 

    Lift the lower metal case up off the upper metal case and internal components.

    Set the lower metal case aside.

16. Unscrew the power supply and fan

    • 

    Flip the console over.

    Use a T10 Torx screwdriver to remove the following screws securing the power supply and fan to the upper metal case:

    Two 11.4 mm screws

    Two 11.4 mm screws

    One 11.4 mm screw

17. Loosen the disc drive

    • 
    • 

    Flip the console over.

    Lift the disc drive up so that its metal tab is unhooked from the power supply.

    Place the disc drive on the upper metal case so that it sits over the hard drive. You'll need enough space to unplug the power supply from the motherboard.

18. Unstick the foam tape near the power supply

    • 
    • 
    • 

    Insert the flat end of the spudger underneath the dark grey foam tape starting at the corner closest to the power supply and edge of the console.

    Lift up the corner.

    Slowly push the spudger through to the other side of the tape until you can see the flat end emerge.

19. Move the power supply

    • 
    • 

    Lift the power supply directly upward to unplug it from the motherboard.

20. Step 20

    • 
    • 

    Lift the power supply so that the cables are at a 90 degree angle.

21. Step 21

    • 
    • 

    While holding the power supply above the console, move the two grey cables out of the plastic hook on the fan case.

22. Step 22

    • 

    Set the power supply on the table.

23. Unplug the fan from the motherboard

    • 
    • 

    Unplug the bundled cable connector connecting the fan to the motherboard by pulling directly upward.

24. Remove the fan

    • 
    • 

    Lift the fan case up to remove it from the console.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Xbox One X Answers community for help.