Xbox One X Hard Drive Replacement

Werkzeuge

• ESD Safe Blunt Nose Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
• TR10 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
• TR8 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Ersatzteile

• Xbox One X HDD and Bracket Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →

Anleitung

1. Remove the sticker

   • 
   • 

   Use blunt tweezers to peel off the sticker covering the right-side screw on the back of the console.

2. Remove the external screws

   • 

   Use a T10 Torx screwdriver to remove the two 12.6 mm–long screws located on the back of the console.

3. Slide the upper case horizontally

   • 
   • 

   Rotate the console 90 degrees.

   Pull the front of the upper plastic case horizontally toward the front of the console until it comes to a stop. This slides the clips out of the slots on the upper plastic case.

4. Lift the upper case off the lower case

   • 
   • 

   Rotate the console 90 degrees so that the back is facing you.

   Lift up the left side of the upper plastic case (as viewed from the back of the console), stopping when it won’t lift any further.

5. Step 5

   • 
   • 
   • 

   While continuing to hold the left side of the upper plastic case, push up on the right side to move the right-side screw boss out of the way.

   Swing the upper plastic case open to 75 degrees.

6. Step 6

   • 
   • 

   Push the upper plastic case down and away from the console to remove it completely.

7. Disconnect the ribbon cable

   • 
   • 
   • 

   Use the pointed end of a spudger, an opening tool, or your fingernail to flip down the small, hinged locking flap on the ribbon cable ZIF connector on the front circuit board.

8. Disconnect the ribbon cable

   • 

   Use blunt tweezers to pull the ribbon cable down out of the connector.

9. Remove the front circuit board screws

   • 

   Use a T8 Torx screwdriver to remove the three 13.3 mm screws securing the front circuit board to the upper metal case.

10. Remove the front circuit board

    • 
    • 

    Pull the front circuit board straight out away from the upper metal case and set it aside.

11. Remove the upper metal case screws

    • 

    Use a T10 Torx screwdriver to remove the six 47.7 mm screws securing the upper metal case to the lower plastic case.

    Use a T8 Torx screwdriver to remove the two 7.5 mm screws securing the press connector to the upper metal case.

12. Detach the press connector

    • 
    • 

    Insert the flat end of a spudger underneath the press connector on the side opposite of the ribbon cable.

    Use the spudger to lift the press connector up and away from the upper metal case.

13. Remove the lower plastic case

    • 
    • 
    • 

    Flip the console over.

    Lift the lower plastic case up from the metal case and set it aside.

14. Remove the lower metal case screws

    • 

    Remove the two T10 Torx screws securing the lower metal case:

    One 7.7 mm screw

    One 11.4 mm screw

15. Remove the lower metal case

    • 

    Lift the lower metal case up off the upper metal case and internal components.

    Set the lower metal case aside.

16. Remove the screws holding the hard drive to the case

    • 

    Flip the console over.

    Use a T10 Torx screwdriver to remove the four 11.4 mm screws securing the hard drive to the upper metal case.

17. Move the disc drive

    • 
    • 
    • 

    Flip the console back over, keeping in mind the disc drive is loose.

    Lift the disc drive up so that its metal tab is unhooked from the power supply.

    Flip the disc drive over and place it on the power supply. The disc drive should end up facing the opposite direction it started in.

18. Unplug the bundled cable connector

    • 
    • 

    Unplug the bundled cable connector connecting the hard drive to the motherboard by pulling directly upward.

19. Unplug the SATA cable

    • 
    • 

    Unplug the SATA cable connecting the hard drive to the motherboard by pulling directly upward.

20. Remove the hard drive

    • 
    • 

    Lift the hard drive assembly up out of the upper metal case.

21. Remove the mounting bracket

    • 

    Flip the hard drive over so that the plastic mounting bracket is facing upward.

    Use a T10 Torx screwdriver to remove the four 8.6 mm screws attaching the hard drive to the mounting bracket.

22. Step 22

    • 
    • 

    Lift the mounting bracket off the hard drive.

23. Unplug the hard drive connector

    • 
    • 

    Unplug the hard drive connector from the hard drive by pulling parallel to the length of the drive.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Xbox One X Answers community for help.