Xbox Series S SSD Card Replacement
Follow this guide to remove and replace the SSD card on a Xbox Series S.
There are some photo discontinuities with the exterior Bluetooth, Wifi, and power boards. These discontinuities do not affect the repair procedure.
Lieber von uns ausführen lassen? Angebot innerhalb eines Werktages.
Werkzeuge
-
Spudger Verfügbarkeit: Bestellbar Im Shop ansehen →
-
TR10 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
TR8 Torx Security Screwdriver Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
-
Tweezers Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Ersatzteile
- Xbox Series S SSD Verfügbarkeit: Externe Bezugsquelle Bei iFixit kaufen →
Anleitung
-
Peel off the sticker coverings
Use tweezers to peel off the two white screw covers located on the bottom corners of the back panel.
-
-
Remove the back panel screws
Use a T8 Torx driver to remove the two 10 mm-long screws securing the back panel to the bottom panel.
-
-
Remove the bottom panel
Slide the bottom panel horizontally toward the back of the console until it comes to a stop.
Lift straight up and remove the bottom panel from the plastic case.
-
-
Remove the plastic case screws
Use a T10 Torx driver to remove the seven 51 mm-long screws securing the chassis to the plastic case.
-
-
Remove the plastic case
With the bottom of the Xbox facing you, pull the two bottom-rear corners of the plastic case away from each other.
As you pull the corners apart, slide the back panel towards the bottom of the device. This releases the back panel from the plastic case.
-
-
Step 6
Pull the bottom-left corner away from the chassis while swinging the chassis away from the plastic case.
Remove the plastic case from the chassis.
-
-
Remove the power button board
Use a T8 Torx driver to remove the 9.5 mm-long screw securing the power button board to the chassis.
-
-
Step 8
Use a spudger to pry and loosen the power button board.
Pull the power button board straight out to disconnect it from the chassis.
-
-
Remove the Wi-Fi board
Use a T8 Torx driver to remove the three 9.5 mm-long screws securing the Wi-Fi board to the short edge of the chassis.
-
-
Step 10
Use a spudger to pry and loosen the Wi-Fi board.
Pull the Wi-Fi board straight out to disconnect it from the chassis.
-
-
Remove the Bluetooth board
Use a T8 Torx driver to remove the three 9.5 mm-long screws securing the Bluetooth board to the long edge of the chassis.
-
-
Step 12
Use a spudger to pry and loosen the Bluetooth board.
Pull the Bluetooth board straight out to disconnect it from the chassis.
-
-
Remove the power supply screws
Use a T10 Torx driver to remove the seven 11.3 mm-long screws securing the power supply to the chassis.
-
-
Remove the upper chassis
Flip the device over.
Lift the upper chassis straight up to remove it.
-
-
Remove the power supply
Lift the power supply straight up to disconnect it from the motherboard.
Remove the power supply.
-
-
Remove the fan screws
Use a T10 Torx driver to remove the two 11.3 mm-long screws securing the fan to the chassis.
-
-
Disconnect the fan
Flip the device over.
Use your fingers to pull and disconnect the fan connector from its motherboard socket.
-
-
Remove the fan
Lift the fan straight up to remove it from the motherboard.
-
-
Remove the motherboard screws
Use a T8 Torx driver to remove the four 9.4 mm-long screws securing the motherboard to the chassis.
-
-
Remove the locking clip
Flip the device over.
Insert a spudger into the locking clip located on the front-left corner of the chassis.
Lift straight up to remove the clip.
-
-
Remove the motherboard
Grasp the heat sink with your fingers and lift up the front of the motherboard up above the edge of the chassis.
Pull the motherboard towards the front of the chassis to remove it.
-
-
Remove the SSD card
Use a T8 Torx driver to remove the 5.1 mm-long screw securing the SSD card to the motherboard.
-
-
Step 23
Pull the SSD card straight out and remove it from the motherboard.
-
Abschluss
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.